I am rebuilding a B2000 from an ignite boot image and on boot up, the system
does not recognise that it has a hard disk installed. I have tried the disk
in both the SCSI 6 and SCSI 5 positions. The disk is spinning in both slots.

The unit does recognise the CD-ROM drive and an externally connected DAT
tape drive. I enclose the output from the system below. Any help you could
give would be most appreciated

================================================== ======
NOTE: System rebooting...

Firmware Version 5.0

Duplex Console IO Dependent Code (IODC) revision 1

------------------------------------------------------------------------------
(c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

Processor Speed State Coprocessor State I/D Cache
--------- -------- --------------------- ----------------- -------------
0 400 MHz Active Functional 512 kB/1
MB

Central Bus Speed: 120 MHz

Available memory: 268435456 bytes
Good memory required: 16547840 bytes

Primary boot path: SCSI.6.0
Alternate boot path: SCSI.5.0
Console path: GRAPHICS(0)
Keyboard path: USB

Processor is booting from first available device.

To discontinue, press any key within 10 seconds.

10 seconds expired.
Proceeding...

Searching for device(s) with bootable media...
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).

Attempting to boot Primary Path...
Attempted boot failed, continuing search

Attempting to boot Alternate Path...
Attempted boot failed, continuing search

Attempting to boot first valid device on FWSCSI ...
Module not found, continuing search

Attempting to boot first valid device on PCI1 ...
Module not found, continuing search

Attempting to boot first valid device on PCI2 ...
Attempted boot failed, continuing search

Attempting to boot first valid device on PCI3 ...
Attempted boot failed, continuing search

Attempting to boot first valid device on PCI4 ...
Module not found, continuing search

Attempting to boot first valid device on SCSI ...
Attempted boot failed, continuing search

Attempting to boot first valid server on LAN ...
Attempted boot failed, continuing search

Attempting to boot first valid device on IDE ...

BOOTABLE DEVICE FOUND:
Path Number Device Path Device Type and Utilities
----------- ----------------- -------------------------
P0 IDE FX4830T
IPL

Booting...
Boot IO Dependent Code (IODC) revision 0


HARD Booted.

ISL Revision A.00.38 OCT 26, 1994

ISL booting hpux (;0):INSTALL

Boot
: disk(10/0/14/0.0.0.0.0.0.0;0):INSTALL
6114188 + 737280 + 409824 start 0x195068
0 STIME0: 0c
4c: STEST3: 80 STEST2: 00 STEST1: 0c STEST0: 07
50: RESV50: 80 STEST4: e0 SIDL1: 00 SIDL0: 00
54: RESV54: 00 RESV55: 00 SODL1: 00
System Console is on the Built-In Serial Interface
Networking memory for fragment reassembly is restricted to 23846912 bytes
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - no room
WARNING: No dump device configured. Dump is disabled.
Starting the STREAMS daemons.
9245XB HP-UX (B.10.20) #1: Sun Jun 9 06:31:19 PDT 1996

Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 262144 Kbytes, lockable: 190496 Kbytes, available: 220120
Kbytes

======= 10/17/04 05:51:51 EDT HP-UX Installation Initialization. (Sun Oct
17
05:51:51 EDT 2004)
@(#) Ignite-UX Revision A.2.6.358
@(#) install/init (opt) $Revision: 10.201 $
* EISA configuration has completed. Following the completion of a
successful HP-UX installation, please check the
"/etc/eisa/config.err"
file for any EISA configuration messages.
* Scanning system for IO devices...
* Querying graphics device: 10/1/0/0 ...
NOTE: Primary path not currently set to an existing disk device.
* Setting keyboard language.

A USB interface has been detected on this system.
In order to use a keyboard on this interface, you must specify
a language mapping which will be used by X windows and
the Internal Terminal Emulator (ITE).
The characters "1234567890" will appear as "!@#$^&*()"
on keyboards that use the shift key to type a number.
Your choice will be stored in the file /etc/kbdlang


1) USB_PS2_DIN_Belgian 2) USB_PS2_DIN_Belgian_Euro
3) USB_PS2_DIN_Danish 4) USB_PS2_DIN_Danish_Euro
5) USB_PS2_DIN_Euro_Spanish 6) USB_PS2_DIN_Euro_Spanish_Euro
7) USB_PS2_DIN_French 8) USB_PS2_DIN_French_Euro
9) USB_PS2_DIN_German 10) USB_PS2_DIN_German_Euro
11) USB_PS2_DIN_Italian 12) USB_PS2_DIN_Italian_Euro
13) USB_PS2_DIN_JIS_109 14) USB_PS2_DIN_Korean
15) USB_PS2_DIN_Norwegian 16) USB_PS2_DIN_Norwegian_Euro
17) USB_PS2_DIN_S_Chinese 18) USB_PS2_DIN_Swedish
19) USB_PS2_DIN_Swedish_Euro 20) USB_PS2_DIN_Swiss_French2_Euro
21) USB_PS2_DIN_Swiss_German2 22) USB_PS2_DIN_Swiss_German2_Euro
23) USB_PS2_DIN_T_Chinese 24) USB_PS2_DIN_UK_English
25) USB_PS2_DIN_UK_English_Euro 26) USB_PS2_DIN_US_English
27) USB_PS2_DIN_US_English_Euro

Enter the number of the language you want: 24

You have selected the keyboard language USB_PS2_DIN_UK_English.
Please confirm your choice by pressing RETURN or enter a new number:


Welcome to Ignite-UX!

Use the <tab> key to navigate between fields, and the arrow keys
within fields. Use the <return/enter> key to select an item.
Use the <return> or <space-bar> to pop-up a choices list. If the
menus are not clear, select the "Help" item for more information.

Hardware Summary: System Model: 9000/785/B2000
+---------------------+----------------+-------------------+ [ Scan
gain ]
| Disks: 0 ( 0.0GB) | Floppies: 0 | LAN cards: 2 |
| CD/DVDs: 1 | Tapes: 1 | Memory: 256Mb |
| Graphics Ports: 1 | IO Buses: 4 | CPUs: 1 | [ H/W
Details ]
+---------------------+----------------+-------------------+

[ Install HP-UX ]

[ Run a Recovery Shell ]

[ Advanced Options ]


[ Reboot ] [ Help ]

================================================== ==========


--

Regards

David Coles
david.coles5@ntlworld.com